ACR Forum banner
1 - 20 of 20 Posts

·
Registered
Joined
·
71 Posts
Discussion Starter · #1 ·
I'd like to hear folks opinions regarding their favorite BUIS for their ACR

Does anyone have any experience with Troy's micro BUIS tritium. I'm curious if Troy used tritium inserts that can be replaced.
 

·
Registered
Joined
·
2,790 Posts
There is nothing wrong with Troy micros. I went with the regular height Troy's because I like an absolute co-witness. The Troy micros will only give you a lower 1/3 with the most popular optics mounts. Either will work, it's just a personal preference.
 

·
Registered
Joined
·
64 Posts
I emailed Larue today and they said the Troy Micros would absolute co-witness with their LT660HK mount for the Aimpoint Micro T-1. I hope that's correct.
 

·
Registered
Joined
·
1,587 Posts
thats the setup i use and i'm pretty sure its lower 1/3 although i like it that way personally
Same set up I use too.

As for the tritium, don't know. But that stuff lasts for better than a decade and if it needs replaced then it wouldn't be much trouble to buy a new post and aperture.
 

·
Registered
Joined
·
1,273 Posts

·
Registered
Joined
·
71 Posts
Discussion Starter · #10 ·
Tackelberry23 - I noticed the DOA version on their site. I'd like to hear feedback if anyone here has tried them.
 

·
Registered
Joined
·
45 Posts
I have the DOA version and regular. I shoot a lot better with the regular. I guess it has something to do with the way my eye adjusts to the diamond. I do think that the DOA might be better at long distances due to the secondary aperture but my range is only 100yards so I can't say for certain. I would recommend the regular.
 

·
Registered
Joined
·
2,790 Posts
I have the DOA version and regular. I shoot a lot better with the regular. I guess it has something to do with the way my eye adjusts to the diamond. I do think that the DOA might be better at long distances due to the secondary aperture but my range is only 100yards so I can't say for certain. I would recommend the regular.
Thank you for the report, I was thinking bout the DOA version as well. Guess I'll stick with the regular peep.

:cool:
 

·
Registered
Joined
·
8 Posts
The squared design of the stock Magpuls made it impossible for me to get a decent sight picture, so I went with the regular-height Troys. The co-witness perfectly with my EO Tech sight.
 

·
Registered
Joined
·
1,932 Posts
I use MBUS GenII.I have Troy BUIS micros they ab. co wit. to my SPARC,but im selling them.Dont like themicros perfer a reg sized dot.
 

·
Registered
Joined
·
1,273 Posts
The squared design of the stock Magpuls made it impossible for me to get a decent sight picture, so I went with the regular-height Troys. The co-witness perfectly with my EO Tech sight.
Do you have an XPS or a standard height EOtech? I was considering getting some micros, but I would prefer absolute (dead center) co-witness.
 

·
Registered
Joined
·
45 Posts
Standard height eotechs offer absolute cowitness with regular troys. I use a xps and have absolute co witness. Only eotechs with riser mounts do 1/3 witness.
 

·
Registered
Joined
·
1,273 Posts
Standard height eotechs offer absolute cowitness with regular troys. I use a xps and have absolute co witness. Only eotechs with riser mounts do 1/3 witness.
Excellent, Darwin. Thanks.
 

·
Registered
Joined
·
610 Posts
Standard height eotechs offer absolute cowitness with regular troys. I use a xps and have absolute co witness. Only eotechs with riser mounts do 1/3 witness.
Absolutely. My EXPS makes 1/3 co/witness since it sits higher than the XPS.
 

·
Registered
Joined
·
7 Posts
Knights Armament micros with 600m rear... also a 1/3 co-witness but absolutely satisfied with their performance and quality.
 
1 - 20 of 20 Posts
Top